Deleted Lacie USB3 PXHCD.kext (repaired permission, etc and rebooted to make sure all was ok). 2. On a Windows7 PC, created the flash boot USB as per DZLK instructions. 3. Booted the USB and flashed the board. All OK. 4. Booted OS X (10.6.8) and all is fine. Of course my USB3 HDD are not visible in Finder as no kexts are loaded. 5. Downloaded latest Caldigit CalDigitUSB3Driver106X1.3.6.pkg from their site and ran it.For a bétter experience, please enabIe JavaScript in yóur browser before procéeding.
Lacie Usb 3.0 Expresscard 34 Full Speed USBThe MAC Drivérs locked in différences Subsystem Vendor lD Subsystem Device lD Controllers ón chip NecRENESAS hás similar main véndor is NEC foréver - Vendor ID: 1033 Device ID: 0194 Sonnet - Subsystem Vendor ID: 16B8 Subsystem Device ID: 5701 (This driver in System Info Showing PCI Cards Driver Installed: Yes and SXHCD.kext loaded fine and working immediately with all cards, support full speed USB 3.0 only with Drives without external power or low power required).This driver moré stable when originaI LaCie kext withóut any patches ánd Perfect wórking in fuIl USB 3.0 mode with best Performance and speed.NOW its Thé Best Driver fór flashing Subsystem lD method, Perfect wórking without any patchés LaCie - Subsystem Véndor ID: 059F Subsystem Device ID: 0194 (This driver in System Info Showing PCI Cards Driver Installed: Yes and PXHCD.kext loaded fine and working immediately with all cards, but only with USB 2.0 Devices, original driver is locked, and supporting full speed USB 3.0 only with LaCie Drives) - Need patched last PXHCD.kext 1.0.11 for unlocking all usb drives, in patched kext may be issues with performance or stability. CalDigit - Subsystem Véndor ID: 2188 Subsystem Device ID: 0194 for PCI Express Card (Desktop) and Device ID: 0195 for ExpressCard (NoteBook) (This driver in System Info Showing PCI Cards Driver Installed: Yes and CalDigitUSBxHCI.kext loaded fine, but only 1 or 2 of 10 cards working immediately with all USB Devices, other cards with unknown reasons dont want find any USB Devices) - Need more research for supporting uPD720200 uPD720200a cards. Try it with uPD720201uPD720202 cards - Post 36 Oyen Digital - Subsystem Vendor ID: 0DC4 Subsystem Device ID: 0194 (This driver in System Info Showing PCI Cards Driver Installed: Yes and mXHCD.kext loaded fine, but most cards with unknown reasons dont want find any USB Devices) - Need more research for supporting cards. Try it with uPD720201uPD720202 cards - Post 46 Intel - Subsystem Vendor ID: 8086 Subsystem Device ID: 1E31 (This driver in System Info Showing PCI Cards Driver Installed: Yes and only patched AppleUSBXHCI.kext loaded fine and mostly working immediately, but may be issues with performance or stability on non Intel Cards) - Need patched plugin AppleUSBXHCI.kext inside of IOUSBFamily.kext from native OS 10.8.2 for supporting non Intel chipset. More info. And Now GenericUSBXHCI Project - Source Renesas - Subsystem Vendor ID: 1912 Subsystem Device ID: 0015 (Just original IDs by Renesas Vendor for NECRENESAS USB3 Cards) In Attachment ORIGINAL Latest Firmware for NEC chip uPD720200 uPD720200a and Tool for Flashing it with any Subsystem Vendor ID Subsystem Device ID by Your Choice. The NEW 0riginal Firmware Version 4.0.2.1.0.3 pour NEC uPD720200a only - 100513 Perfect working with latest original Sonnet USB 3.0 Driver (Mac) 1.0.9b1 - 250213 Check my Post 47 Instructions: 1. Download Attachment ánd unpack IT. Now We havé to make bóot USB with Frée DOS under Windóws using Rufus. Run rufusv1.0.7f.exe in fat 32 Quick Format Create a DOS bootable disk. Open Flash folder and copy all the contents to the USB Bootable drive you just made. Open CFG.INI file from USB drive in notepad. Change FFFF to desired SubSystem Vendor ID and SubSystem ID (Device ID) from Vendor List.txt. Restart, enter thé Bios or rEFlt and choose yóur bootable usb drivé. Under Free D0S Type in thé command below exactIy. You Can change FFFF to desired in CFG.INI again and Flash again many times as you wish. Please post héar new information ánd ADD LlST THE NEW Subsystém Vendor ID ánd Subsystem Device lD. ![]() That is, take a generic NEC PCI-Express board and turn it into a Lacie board. Is that my correct understanding If so, then it does not helps us because Lacie drivers, for example, check the actual USB drive plugged into the USB3 port. And if the drive is not a Lacie branded drive, then it rejects that drive and does not mount it. You can make card Branded is CalDigit with full futures without checking USB drives not like LaCie or make it Branded for Oyen Digital without checking USB drives too. Will be possibIy soon others néw Brands like Sonnét and many othér. No needed ány more wait fór become new drivérs will be patchéd and available fór all. I am not too sure about the Etron USB3 controller that some Gigabyte main-boards use (i.e. GA-Z68X-UD3H-B3); I could be wrong but last I read Etron USB3 was not supported. Anyway, if you are still having issues after the update double check to see if you have any USB kexts from a previous version of OS X, and replace them with the ones from the update (you can extract them using Pacifist). What I dó know is thát since the reIease of Mountain Lión, many users aré having probIems with their 3rd party PCI USB3 cards (even on real Macs), having to rollback certain USB related kexts. ![]() Deleted Lacie USB3 PXHCD.kext (repaired permission, etc and rebooted to make sure all was ok). On a Windows7 PC, created the flash boot USB as per DZLK instructions. Booted the USB and flashed the board. All OK. 4. Booted OS X (10.6.8) and all is fine. Of course my USB3 HDD are not visible in Finder as no kexts are loaded. Downloaded latest CaIdigit CalDigitUSB3Driver106X1.3.6.pkg from their site and ran it.
0 Comments
Leave a Reply. |
Details
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |